Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag

Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag
Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag

Smith & Wesson Cylinder Yoke Extractor J Frame Late Model 60 Series. 357 Mag

Up for sale is a Very Nice condition, Cylinder / Yoke / Extractor Assembly in SATIN Stainless Steel It is NOT the Brushed, or Bright Stainless!! , that originated from a well cared-for S&W Model 60-15 Performance Center / Pro Series revolver, chambered in. The Yoke is in Fine condition, with even less evidence of use. The Chambers in the Cylinder are bright and shiny, the Extractor and Center Pin along with their springs are fully functional and responsive, and the Cylinder spins on the Yoke freely, with no noticeable wobble or shake.

PLEASE NOTE This Assembly can ONLY be used on Current / Late-Model J-Frame Revolvers that have a 3-Inch Bbl (or longer), since the Extractor Rod would be too long to fit in the opening under the barrel on a 2-Inch bbl revolver. As for cross-compatibility, we can state that this Cylinder Assembly was used in the S&W Model 60 Pro Series / Performance Center models, such as the Model 60-15. There may be other Current / Late-Model Smith & Wesson revolvers, in the Model 60 Series for example, that this Assembly may be compatible with. WARNING: DO NOT Install this Cylinder Assembly on any revolver that is not originally chambered and barrel marked for. As with any pre-owned gun parts there may be minor imperfections and we have attempted to capture a fair rendition of the condition of the Assembly in the image set.

See photos for full description. A few of the images in the photoset are a collage of the same Assembly taken from two different perspectives: We simply had more images to share than the site's twelve maximum upload limit, so to confirm, this listing is for one Assembly, not two. AND ARE NOT "PROHIBITED ITEMS". What you see is what you receive - no more, no less, unless stated specifically in the listing.

Sales to 48 Continental United States only. All sales are final, unless specifically stated otherwise in the listing. All firearms parts should be inspected and installed by a competent gunsmith. The illegality or unenforceability of any provision of these Terms of Use shall not affect the validity and enforceability of any legal and enforceable provisions of these terms and policies. We have taken reasonable efforts to ensure that the information contained is accurate; however, all information is provided "as is" without any express or implied warranties, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non-infringement.

In addition, by using the information from the listing, you understand and agree that all firearms are potentially dangerous if handled improperly and can pose risks and hazards to yourself and others, which may result in property damage, serious injury or death. This item is in the category "Sporting Goods\Hunting\Gun Parts\Pistol Parts". The seller is "stormchimes" and is located in this country: US. This item can be shipped to United States.