Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY

Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY
Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY

Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY

Up for sale is a Very Nice condition. Clean Recessed Cylinder / Yoke / Extractor Assembly for the Vintage Model 65-2 & 66-1 (ONLY). This particular Assembly originated from a well cared-for S&W Model 65-2 Revolver. It is mechanically sound with strong and responsive Extractor Spring and Center Pin Springs, the Cylinder spins smoothly on the Yoke with no noticeable wobble or play.

The chambers are bright and shiny and there is no evidence whatsoever of any corrosion or pitting ever being present on this Assembly. PLEASE NOTE - COMPATIBLE MODELS INFO: To the best of our knowledge, there are only TWO truly compatible models that S&W manufactured that this Assembly would be a direct, identical replacement for. The reason for this is that the Assemblies used on earlier models (such as the 65-1, and the 66 No Dash) had the Gas Ring on the Yoke itself, versus in the Cylinder on the 65-2 and 66-1 like the Assembly in this listing. As for later models (such as the 65-3 and later Model 65's, and then the 66-2 and later Model 66's), The Cylinders were no longer "Counterbored" (Recessed), meaning the length of the newer cylinders is actually just a fraction shorter that the Cylinder in this listing (and later models also changed the construction of the Yoke Retention System).

The older, longer Cylinder will just barely NOT go back far enough for the Cylinder to swing shut in the frame. In other words, for those who wish to use a Recessed Cylinder from a Model 66-1 on their Model 66-2 that came with a NON-Recessed Cylinder, this swap will simply not work. If you have any questions about interchangeability of the Model 65 or 66 Cylinder Assemblies and would like us to elaborate further, send us a message and we'll be happy to respond promptly to your inquiry. As with any vintage gun parts there may be minor imperfections and we have attempted to capture a fair rendition of the condition of the Assembly in the image set. See photos for full description.

Exactly the Assembly as seen in this listing's photoset. A few of the images in the photoset are a collage of the same Assembly taken from two different perspectives: We simply had more images to share than the site's twelve maximum upload limit, so to confirm, this listing is for one Assembly, not two. As all sales on gun parts are final. What you see is what you receive - no more, no less, unless stated specifically in the listing. Sales to 48 Continental United States only.

All sales are final, unless specifically stated otherwise in the listing. All firearms parts should be inspected and installed by a competent gunsmith. The illegality or unenforceability of any provision of these Terms of Use shall not affect the validity and enforceability of any legal and enforceable provisions of these terms and policies.

We have taken reasonable efforts to ensure that the information contained is accurate; however, all information is provided "as is" without any express or implied warranties, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non-infringement. In addition, by using the information from the listing, you understand and agree that all firearms are potentially dangerous if handled improperly and can pose risks and hazards to yourself and others, which may result in property damage, serious injury or death. The item "Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY" is in sale since Tuesday, August 17, 2021.

This item is in the category "Sporting Goods\Hunting\Gun Parts\Pistol". The seller is "stormchimes" and is located in Wausau, Wisconsin. This item can be shipped to United States.


Smith & Wesson RECESSED Cylinder / Yoke / Extractor Model 66 -1 & 65 -2 ONLY