Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY

Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY
Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY

Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY

Up for sale is a. Fine Condition, clean Complete Cylinder / Yoke / Extractor Assembly that originated from a well cared-for Smith & Wesson Model 66-2 Snub-Nosed revolver chambered in.

357 Magnum, with a 2 1/2 Barrel. The Assembly here is configured for the Model 66 "Snubby" which was a bit more scarce configuration, compared to the more common 4 Inch and 6 inch barreled Model 66's. As for compatible models, please note the following information. Model 66 No Dash: WILL interchange, but chambers are not "Recessed", and the threads on the ejector rod of the listed Assembly here are the later threads that were reversed from the original Model 66 No Dash models...

So that the ejector rod does not come loose when fired. This design change occurred with the switch from the 66 No Dash to the 66-1. Also note the 66 No Dash still had the Gas Ring as part of the Yoke, and that gas ring was switched to the Cylinder on the 66-1. If you use this Assembly on 66 No Dash, you MUST replace the old Yoke and old Cylinder with the new Yoke and New Cylinder, and cannot combine one old part with one new part.

This is CRITICAL to acknowledge, please let us know if you have questions clarifying this. Model 66-1: WILL interchange, but again, the listed Assembly does not have Recessed cuts in chambers. Model 66-2: EXACT, identical replacement. Later models, such as the 66-3 and beyond, made changes to the Yoke Retention System which resulted in the shape of the Yoke Stud changed, and you would no longer be able to use the Yoke that is supplied with this Assembly. There is very little fouling on the face of the cylinder, and the chambers are bright and shiny.

The springs for the Extractor and the Center pin are strong and responsive, and the Extractor Star mates to the cylinder with accuracy. There is no evidence whatsoever of any rust, pitting or corrosion anywhere on any part of this Assembly.

It looks very lightly used, indeed. The Extractor Rod on this Assembly is the SHORT extractor that is designed to match the application of a 2 1/2 Inch Barreled (Snub-Nosed) Model 66... DO NOT USE THIS ASSEMBLY if you have a Model 66 that has a 3", 4" or 6 Barrel, as the Extractor Rod is too short to mate to the end of the Locking Lug towards the front of the barrel on those other, longer-barreled variants. As with any vintage gun parts there may be minor imperfections and we have attempted to capture a fair rendition of the condition of the items in the image set. See photos for full description. Exactly the Assembly as seen in this listing's photoset. A few of the images in the photoset are a collage of the same Assembly taken from two different perspectives: We simply had more images to share than the site's twelve maximum upload limit, so to confirm, this listing is for one Assembly, not two. As all sales on gun parts are final. What you see is what you receive - no more, no less, unless stated specifically in the listing. Sales to 48 Continental United States only.

All sales are final, unless specifically stated otherwise in the listing. All firearms parts should be inspected and installed by a competent gunsmith. The illegality or unenforceability of any provision of these Terms of Use shall not affect the validity and enforceability of any legal and enforceable provisions of these terms and policies.

We have taken reasonable efforts to ensure that the information contained is accurate; however, all information is provided "as is" without any express or implied warranties, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non-infringement. In addition, by using the information from the listing, you understand and agree that all firearms are potentially dangerous if handled improperly and can pose risks and hazards to yourself and others, which may result in property damage, serious injury or death. The item "Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY" is in sale since Saturday, April 3, 2021. This item is in the category "Sporting Goods\Hunting\Gun Parts\Pistol". The seller is "stormchimes" and is located in Wausau, Wisconsin.

This item can be shipped to United States.


Smith & Wesson Model 66 Cylinder / Yoke / Extractor, SNUB 2.5inch Barrels ONLY