Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series

Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series
Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series

Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series

Up for sale is a fine condition, complete UNFLUTED Cylinder / Yoke / Extractor Assembly. That originated from a well cared-for S&W Model 686-6 "Plus" 3-5-7 Series revolver, chambered in. As for compatible models, we only recommend using this Assembly on Late / Current Production Model 7-Round Model 686's, such as the 686-6 7-Round Model, also referred to as the the 686 "Plus" in the 7-Round Model, and the 686-6 Plus "3-5-7 Series" Model line. The Chambers are shiny and bright, the Ejector Rod and Center Pin and their springs are fully-functional, and the Cylinder Spins in the Yoke with no mentionable wobble or play.

Beyond that, this is indeed a fine-looking and fully operational Complete Cylinder Assembly that is seldom seen as a stand-alone part in the Unfluted variant. Please Note Due to the length of the Extractor Rod being full-length, this Assembly is ONLY intended for revolvers that have a 3-Inch Barrel or longer installed.

Otherwise the Extractor Rod would not fit into the cut in the barrel shroud on the 2.5 barreled models! FINAL NOTE Due to engineering changes made between earlier Model 686's and the 686-6 / 686 "Plus" 7-Round revolver that this Assembly was installed on, we do not recommend, nor will we comment about backwards-compatibility for those who are looking to install this Assembly on a revolver earlier than the 686-6 (the most obvious note of incompatibility would be that this is a 7-Round Cylinder, and not a 6-Round Cylinder). DO NOT ATTEMPT to install this Assembly on a 6-Round Model as the timing would be off as well, resulting from a fractional difference in the angle of the tip of the Hand inside the gun as well. As with any pre-owned gun parts there may be minor imperfections and we have attempted to capture a fair rendition of the condition of the Assembly in the image set. See photos for full description.

Exactly the Assembly as seen in this listing's photoset. A few of the images in the photoset are a collage of the same Assembly taken from two or three different perspectives: We simply had more images to share than the site's twelve maximum upload limit, so to confirm, this listing is for one Assembly, not two, nor three of them. As all sales on gun parts are final.

What you see is what you receive - no more, no less, unless stated specifically in the listing. Sales to 48 Continental United States only. All sales are final, unless specifically stated otherwise in the listing.

All firearms parts should be inspected and installed by a competent gunsmith. The illegality or unenforceability of any provision of these Terms of Use shall not affect the validity and enforceability of any legal and enforceable provisions of these terms and policies. We have taken reasonable efforts to ensure that the information contained is accurate; however, all information is provided "as is" without any express or implied warranties, including but not limited to the implied warranties of merchantability, fitness for a particular purpose or non-infringement. In addition, by using the information from the listing, you understand and agree that all firearms are potentially dangerous if handled improperly and can pose risks and hazards to yourself and others, which may result in property damage, serious injury or death.

The item "Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series" is in sale since Tuesday, September 14, 2021. This item is in the category "Sporting Goods\Hunting\Gun Parts\Pistol". The seller is "stormchimes" and is located in Wausau, Wisconsin. This item can be shipped to United States.


Smith & Wesson Cylinder Yoke Extractor Assembly, Model 686 Plus / 3-5-7 Series